-
1 remote communications interface
Automation: RCIУниверсальный русско-английский словарь > remote communications interface
-
2 remote station communications interface equipment
Military: RSCIEУниверсальный русско-английский словарь > remote station communications interface equipment
-
3 интерфейс (для) дистанционной передачи данных
Automation: remote communication interface, remote communications interfaceУниверсальный русско-английский словарь > интерфейс (для) дистанционной передачи данных
-
4 интерфейс дистанционной передачи данных
Универсальный русско-английский словарь > интерфейс дистанционной передачи данных
-
5 дистанционный интерфейс
Engineering: remote communications interfaceУниверсальный русско-английский словарь > дистанционный интерфейс
-
6 аппаратура сопряжения средств связи периферийной станции
Универсальный русско-английский словарь > аппаратура сопряжения средств связи периферийной станции
-
7 параллельная система ИБП
параллельная система ИБП
-
[Интент]Parallel Operation: The system shall have the option to install up to four (4) UPSs in parallel configuration for redundancy or capacity.
1. The parallel UPS system shall be of the same design, voltage, and frequency. UPS modules of different size ratings shall be permitted to be paralleled together for purposes of increased capacity or UPS module redundancy. The UPSs in the parallel configuration shall not be required to have the same load capacity rating.
2. Parallel Capacity: With N+0 system-level redundancy, up to 2MW of load can be supported by the system.
3. Parallel Redundancy: With N+1 system-level redundancy, up to 1.5MW of load can be supported by the system, and only the UPS being replaced must be isolated from the source (bypass operation is not required for the entire system during the UPS replacement procedure).
4. Output control: A load sharing circuit shall be incorporated into the parallel control circuits to ensure that under no-load conditions, no circulating current exists between modules. This feature also allows each UPS to share equal amounts of the total critical load bus. The output voltage, output frequency, output phase angle, and output impedance of each module shall operate in uniformity to ensure correct load sharing. This control function shall not require any additional footprint and shall be an integral function of each UPS. The static bypass switches shall be connected in parallel.
5. Parallel System Controls: To avoid single points of failure, the UPS system shall have no single dedicated control system designed to control the operation of the parallel UPS system. Control of and direction of parallel UPSs shall take place via a master/slave relationship, where the first UPS to receive logic power asserts itself as a master. In the event of a master failure, a slave UPS shall take the role of master and assume the responsibility of the previous master UPS. Regardless of which UPS is master or slave, user changes to the system status, such as request for bypass, can be done from any UPS connected to the bus and all UPS on the bus shall transfer in simultaneously.
6. Communication: Communication between modules shall be connected so that the removal of any single cable shall not jeopardize the integrity of the parallel communication system. Load sharing communications shall be galvanically isolated for purposes of fault tolerance between UPS modules. A UPS module's influence over load sharing shall be inhibited in any mode where the UPS inverter is not supporting its output bus. Transfers to and from bypass can be initiated from any online UPS in the system.
7. Display: Each UPS multi-color LCD touch screen user interface shall be capable of using an active touch screen mimic bus to show the quantity of UPS(s) connected to the critical bus, as well as the general status of each UPS, such as circuit breaker status information. Any touchscreen display shall support the configuration of the [entire parallel] system and shall provide event and alarm data for all UPSs in the parallel configuration. A Virtual Display Application shall be available for download to the customer’s computer and shalll support remote monitoring of a complete system with up to 4 UPSs in parallel.
8. Battery runtime: Each UPS must have its own battery solution. The battery solution for the entire system can be a combination of standard and third-party batteries, but each UPS must use only one battery solution – either standard or third-party batteries.
9. Switchgear: A custom switchgear option shall be required for parallel operation.
[Schneider Electric]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > параллельная система ИБП
См. также в других словарях:
Remote Desktop Services — Developer(s) Microsoft Stable release 7.0 (6.1.7600) / October 27, 2009 … Wikipedia
Remote Direct Memory Access — (RDMA) allows data to move directly from the memory of one computer into that of another without involving either one s operating system. This permits high throughput, low latency networking, which is especially useful in massively parallel… … Wikipedia
Remote virtual media — is a method of connecting a remote media source (i.e. CD ROM drive, hard disk drive, floppy disk drive, or virtual implementation of any of them) to a local system. The local system then has access to the remote (and possibly virtual) media and… … Wikipedia
Communications protocol — For other senses of this word, see Protocol. A communications protocol is a system of digital message formats and rules for exchanging those messages in or between computing systems and in telecommunications. A protocol may have a formal… … Wikipedia
Remote laboratory — This article is about the use of telecommunications in conducting experiments. For India s virtual labs projectl, see Virtual Labs (India). . Remote laboratory (also known as online laboratory, remote workbench) is the use of telecommunications… … Wikipedia
Remote control — For other uses, see Remote control (disambiguation). A television remote control unit (RCU) A remote control is a component of an electronics device, most commonly a television set, used for operating the television device wireless … Wikipedia
Open Service Interface Definitions — (OSIDs) are programmatic interface specifications describing services. These interfaces are specified by the Open Knowledge Initiative (O.K.I.) to implement a Service Oriented Architecture (SOA) to achieve interoperability among applications… … Wikipedia
Message Passing Interface — MPI, the Message Passing Interface, is standardized and portable message passing system designed by a group of researchers from academia and industry to function on a wide variety of parallel computers. The standard defines the syntax and… … Wikipedia
Cisco Unified Communications Manager — (CUCM), formerly Cisco Unified CallManager and Cisco CallManager (CCM), is a software based call processing system developed by Cisco Systems. CUCM tracks all active VoIP network components; these include phones, gateways, conference bridges,… … Wikipedia
Application programming interface — API redirects here. For other uses, see API (disambiguation). An application programming interface (API) is a source code based specification intended to be used as an interface by software components to communicate with each other. An API may… … Wikipedia
Radio communications during the September 11 attacks — This article reviews some of the details of radio communications at the September 11, 2001 World Trade Center attacks. [The purpose of revealing the operational details in this article is to allow operators of other communications networks and… … Wikipedia